Your specialist in diesel technology
No vehicle selected Select make, model and engine

Loading...
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

S
Selected vehicle
Show matching parts
Vehicle search Select make, model and engine
Loading...
  1. 1 Make
  2. 2 Model
  3. 3 Engine / type
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

P20EE: SCR efficiency below threshold – causes, diagnosis and fixes

DieselFix Neuss |

The engine warning light comes on, an AdBlue or emissions warning appears – maybe even a countdown to a no-start – and the fault memory shows P20EE. The engine control unit has found that the SCR system is not reducing nitrogen oxides (NOx) enough. Before replacing an expensive catalyst, it is worth checking AdBlue, dosing and the NOx sensors.

What does P20EE mean?

P20EE – SCR NOx catalyst efficiency below threshold, bank 1
The engine control unit compares the NOx values before and after the SCR catalyst. If the NOx content after the catalyst does not drop enough, P20EE is stored.

Note: the meaning is defined by the OBD-II standard; some manufacturers add their own sub-codes. Always read the complete fault memory including the freeze-frame data.

Typical symptoms

  • Engine warning light and an AdBlue or emissions warning
  • Depending on the manufacturer, a countdown to a no-start ("engine start not possible in … miles")
  • Reduced power
  • Sometimes a sharp smell of ammonia at the exhaust
  • Higher or unusually low AdBlue consumption

The most common causes

CauseHow to check itNote
Poor AdBlue quality (diluted, too old, contaminated)Measure the urea content with a refractometer (target 32.5 %), drain and refill if necessarySimple first step
Blocked or crystallised AdBlue dosing injectorLook for white crystals, run a dosing quantity test with a diagnostic toolCommon with lots of short trips
NOx sensor before or after the SCR catalyst giving wrong readingsCompare NOx values before and after the catalyst with dosing activeNOx sensors age and become inaccurate
AdBlue pump, line or heaterCheck system pressure and heating, especially in winter
Exhaust leak upstream of a NOx sensorCheck the exhaust system for leaksDistorts the measurement
High raw NOx emissions from the engine (e.g. EGR fault)Check other fault codes and EGR operationThe SCR system can no longer keep up
Aged or contaminated SCR catalystOnly after ruling out the other causesMost expensive fix

Step-by-step diagnosis

  1. Read the complete fault memory: related codes for the NOx sensors (e.g. P2200, P229F), AdBlue dosing or EGR give important clues.
  2. Check the AdBlue quality and refill the tank if in doubt.
  3. Run a dosing quantity test and check the dosing injector for crystals.
  4. Compare NOx values before and after the SCR catalyst in live data: with a warm catalyst and dosing active, the downstream value must be clearly lower. Implausible values point to a NOx sensor.
  5. Check the exhaust for leaks and ask the manufacturer about software updates.
  6. Only then assess the SCR catalyst.

Can I keep driving with P20EE?

In the short term, usually yes. However, many Euro 6 vehicles start a countdown: if the cause is not fixed, the engine cannot be restarted once it reaches zero. So have the fault checked in good time.

If a NOx sensor is faulty

Find NOx sensors for your vehicle here: NOx sensors. Pay attention to the fitting position: the sensors before and after the SCR catalyst often have different part numbers. More guides: Faulty NOx sensor? 5 warning signs and Ammonia smell from the exhaust.

Frequently asked questions

Is the SCR catalyst always faulty with P20EE?

No. AdBlue quality, a blocked dosing injector or a NOx sensor reading incorrectly are often the cause. The catalyst is the last step of the diagnosis.

Does a new NOx sensor need to be calibrated?

Depending on the manufacturer, learned values must be reset or an adaptation carried out with a diagnostic tool after replacement.

Which NOx sensor is the right one – before or after the catalyst?

The related codes and live values tell you. Also compare the part number on the installed sensor.

Does simply refilling with fresh AdBlue help?

If quality was the cause, yes – after refilling, clear the fault and do a test drive. With other causes, P20EE will come back.

Leave a comment

Please note: comments must be approved before they are published.

Delivery country

Prices and refundable deposits depend on the delivery country. Your language selection stays unchanged.