Your specialist in diesel technology
No vehicle selected Select make, model and engine

Loading...
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

S
Selected vehicle
Show matching parts
Vehicle search Select make, model and engine
Loading...
  1. 1 Make
  2. 2 Model
  3. 3 Engine / type
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

P2200, P2201, P2202 and P229F: NOx sensor circuit faults – causes, diagnosis and fixes

DieselFix Neuss |

The engine warning light comes on, often together with an AdBlue or emissions warning, and the fault memory shows P2200, P2201, P2202 or P229F. The engine control unit is reporting that a NOx sensor is not delivering plausible values or that its circuit is disturbed. Check the connector, wiring and power supply before ordering a sensor.

What do P2200, P2201, P2202 and P229F mean?

P2200 / P2201 / P2202 / P229F – NOx sensor circuit
P2200: NOx sensor circuit, bank 1 sensor 1
P2201: NOx sensor circuit range/performance, bank 1 sensor 1
P2202: NOx sensor circuit low, bank 1 sensor 1
P229F: NOx sensor circuit range/performance, bank 1 sensor 2

Note: the meaning is defined by the OBD-II standard; some manufacturers add their own sub-codes. Always read the complete fault memory including the freeze-frame data.

Sensor 1 is the upstream NOx sensor before the SCR catalyst (after the oxidation catalyst or the DPF, depending on the layout). Sensor 2 sits downstream of the SCR catalyst and monitors how well it works. A NOx sensor consists of a probe in the exhaust and its own control unit, which sends the readings to the engine ECU via CAN bus. Related codes are P2203 (circuit high), P2204 (intermittent) and U-codes for lost communication, e.g. U029D or U029E. How the sensor works is explained here: The NOx sensor in a diesel.

Typical symptoms

  • Engine warning light, often with an AdBlue or emissions warning
  • AdBlue dosing reduced or switched off
  • Depending on the manufacturer, a countdown to a no-start
  • Follow-up code P20EE (SCR efficiency below threshold)

The most common causes

CauseHow to check itNote
Corroded or loose connector, water in the connectorOpen the connector at the sensor control unit, look for corrosion and moistureMost common and cheapest cause
Wiring melted on the hot exhaust or chafed throughInspect the harness along the exhaustOften after work on the exhaust
Fuse or power supplyCheck fuse, supply and ground at the sensor control unitCheck first if there are U-codes
CAN wiring faultCheck CAN high/low for open circuit, short and resistanceTypical with U029D/U029E
Sensor not ready or contaminated (soot, oil, coolant, AdBlue crystals)Check status and heater readiness, inspect the probeContamination usually has its own cause
Real exhaust problem (upstream leak, EGR fault, faulty injector)Check for leaks, assess EGR and injectionMainly relevant for P2201/P229F
Faulty NOx sensorOnly after ruling out the other causesProbe and control unit are usually one assembly
Engine control unit softwareAsk the manufacturer about updatesKnown on some models

Step-by-step diagnosis

  1. Read the complete fault memory: which sensor (1 or 2) is affected, are there U-codes or P20EE?
  2. Check live data: NOx value in ppm, sensor status and heater readiness with a warm engine.
  3. Inspect the connector and harness, especially near hot exhaust parts.
  4. Measure supply voltage and ground at the sensor control unit, then check the CAN lines.
  5. Compare sensor 1 and sensor 2 values: with a warm SCR catalyst and dosing active, sensor 2 must read clearly less NOx. More: P20EE: SCR efficiency below threshold.
  6. Check the exhaust upstream of the sensor for leaks.
  7. After replacement: clear the codes and run the adaptation or reset the manufacturer requires.

Can I keep driving with P2200?

In the short term, usually yes – the engine normally runs as usual. Without valid NOx readings, however, many vehicles restrict AdBlue dosing, and some Euro 6 models start a countdown to a no-start. Have it checked soon.

If the NOx sensor is the cause

If connector, wiring, supply and CAN are fine, replacement is the fix. New NOx sensors by vehicle: NOx sensors. Sensor 1 and sensor 2 often have different part numbers. More guides: Faulty NOx sensor? 5 warning signs, Replacing and calibrating a NOx sensor, OEM or aftermarket? and Ammonia smell from the exhaust.

Frequently asked questions

Is the NOx sensor always faulty with P2200?

No. Connectors, damaged wiring or the power supply are often to blame. The sensor comes last.

What is the difference between P2200 and P229F?

P2200 to P2202 refer to sensor 1 before the SCR catalyst, P229F to sensor 2 after it.

Does a new NOx sensor need to be calibrated?

Depending on the manufacturer, an adaptation or a reset of learned values is required.

Leave a comment

Please note: comments must be approved before they are published.

Delivery country

Prices and refundable deposits depend on the delivery country. Your language selection stays unchanged.